## Documentation |

This example shows how to design an infinite-horizon model predictive controller by setting the weights on the terminal predicted states.

On this page… |
---|

Design an Infinite-Horizon LQR Controller Convert the LQR Controller Into a Finite-Horizon MPC Controller |

The linear open-loop dynamic model is defined below. DC gain is also computed.

Ts = 0.1; % Sampling time A = [0.8 Ts;0 0.9]; B = [0;Ts]; C = [1 0]; sysd = ss(A,B,C,0,Ts); % Discrete-time plant model dcg = dcgain(sysd); % DC-gain of prediction model

**Design an Infinite-Horizon LQR Controller**

Compute the Riccati matrix associated with the LQR problem with output weight `Qy` and input weight `Qu`:

Qy = 10; % Output weight: y'*Qy*y Qu = 0.1; % Input weight: u'*Qu*y [K,P] = lqry(sysd,Qy,Qu); % LQR gain and Riccati matrix

Weight the terminal state `x'(t+p)*P*x(t+p)`, where `p` is the prediction horizon of the MPC controller. Compute the Cholesky factor `chol(P)` of the Riccati matrix `P`, so that the terminal penalty becomes:

`x'(t+p)*P*x(t+p) = [chol(P)*x(t+p)]'*[chol(P)*x(t+p)] = yc'(t+p)*yc(t+p)`

where the new output `yc(t+p) = chol(P)*x(t+p)` and the state `x(t)` is assumed to be fully measurable.

cholP = chol(P);

Change and augment the output vector to include the full state `x` and `yc`: Output = state vector x + output yc such that yc'*yc = x'*P*x

sysd.C = [eye(2);cholP]; sysd.D = zeros(4,1);

**Convert the LQR Controller Into a Finite-Horizon MPC Controller**

Label the new additional output signal yc(t) as unmeasured:

sysd = setmpcsignals(sysd,'UO',[3 4]); % Cholesky factor is not measured

-->Assuming unspecified output signals are measured outputs.

Create the controller object with sampling period, prediction and control horizons:

p = 3; % Prediction horizon (for any p>=1, unconstrained MPC = LQR) m = p; % Control horizon = prediction horizon mpcobj = mpc(sysd,Ts,p,m); % MPC object

-->The "Weights.ManipulatedVariables" property of "mpc" object is empty. Assuming default 0.00000. -->The "Weights.ManipulatedVariablesRate" property of "mpc" object is empty. Assuming default 0.10000. -->The "Weights.OutputVariables" property of "mpc" object is empty. Assuming default 1.00000. for output(s) y1 and zero weight for output(s) y2 y3 y4

Specify actuator saturation limits as MV constraints.

mpcobj.MV = struct('Min',-3,'Max',3);

Define input and output weights at each step of the prediction horizon (terminal weights are set later). Very small weights on input increments are included to make the QP problem associated with the MPC controller positive definite:

mpcobj.Weights.OV = [sqrt(Qy) 0 0 0]; % Output weights (only on original output) mpcobj.Weights.MV = sqrt(Qu); % Input weight mpcobj.Weights.MVRate = 1e-5; % Very small weight on command input increments

Define set-points for the output and input signals:

ry = 1; % Output set point mpcobj.MV.Target = ry/dcg; % Set-point for manipulated variable

Impose the terminal penalty `x'(t+p)*P*x(t+p)` by specifying a unit weight on `yc(t+p) = chol(P)*x(t+p)`. The terminal weight on `u(t+p-1)` remains the same, that is `sqrt(Qu)`:

Y = struct('Weight',[0 0 1 1]); % Weight on y(t+p) U = struct('Weight',sqrt(Qu)); % Weight on u(t+p-1) setterminal(mpcobj,Y,U); % Set terminal weight y'*y = x'*P*x

Since the measured output is the entire state, remove any additional output disturbance integrator inserted by the MPC controller:

setoutdist(mpcobj,'remove'); % Remove additional disturbance integrators

Remove the state estimator by defining the following measurement update equation:

`x[n|n] = x[n|n-1] + I * (x[n]-x[n|n-1]) = x[n]`

Because `setterminal` function resets state estimator to default value, we use `setEstimator` function to change state estimator after `setterminal` is called.

```
setEstimator(mpcobj,[],eye(2)); % State estimate = state measurement
```

**Compare MPC and LQR Controllers**

Compute the gain of the MPC controller when constraints are inactive, and compare it to the LQR gain:

mpcgain = dcgain(ss(mpcobj)); fprintf('\n(unconstrained) MPC: u(k)=[%8.8g,%8.8g]*x(k)',mpcgain(1),mpcgain(2)); fprintf('\n LQR: u(k)=[%8.8g,%8.8g]*x(k)\n\n',-K(1),-K(2));

-->The "Model.Noise" property of the "mpc" object is empty. Assuming white noise on each measured output channel. (unconstrained) MPC: u(k)=[-2.8363891,-2.1454028]*x(k) LQR: u(k)=[-2.8363891,-2.1454028]*x(k)

The state feedback gains are exactly the same.

To run this example, Simulink® is required.

if ~mpcchecktoolboxinstalled('simulink') disp('Simulink(R) is required to run this example.') return end

Define a set-point for the new extended output vector containing `x` and `chol(P)*x`:

```
rx = (eye(2)-A)\B/dcg;
r = [rx;cholP*rx]; % Set point for extended prediction model
```

Simulate closed-loop control of the linear plant model in Simulink. Controller "mpcobj" is specified in the block dialog.

mdl = 'mpc_infinite'; open_system(mdl); % Open Simulink(R) Model sim(mdl); % Start Simulation

The closed-loop response shows good setpoint tracking performance.

```
bdclose('mpc_infinite');
```

Was this topic helpful?