Main Content

Isothermal Liquid Properties (IL)

Physical properties of isothermal liquid

Since R2020a

  • Isothermal Liquid Properties (IL) block

Libraries:
Simscape / Foundation Library / Isothermal Liquid / Utilities

Description

The Isothermal Liquid Properties (IL) block defines the liquid properties that act as global parameters for all the blocks connected to a circuit. The default liquid is water.

Each topologically distinct isothermal liquid circuit in a diagram can have a Isothermal Liquid Properties (IL) block connected to it. If no Isothermal Liquid Properties (IL) block is attached to a circuit, the blocks in this circuit use the properties corresponding to the default Isothermal Liquid Properties (IL) block parameter values.

The Isothermal Liquid Properties (IL) block provides a choice of modeling options:

  • Mixture bulk modulus: either constant or a linear function of pressure

  • Entrained air: zero, constant, or a linear function of pressure

Equations used to compute various liquid properties depend on the selected isothermal liquid model. For detailed information, see Isothermal Liquid Modeling Options.

Ideal Fluid Models

Entrained air is the relative amount of nondissolved gas trapped in the fluid. Fluid with zero entrained air is ideal, that is, it represents pure liquid.

In its default configuration, the Isothermal Liquid Properties (IL) block models an ideal fluid with a constant bulk modulus:

  • Isothermal bulk modulus model is Constant

  • Entrained air model is Constant

  • Entrained air-to-liquid volumetric ratio at atmospheric pressure is 0

In this model, the liquid bulk modulus is assumed to be constant and therefore the liquid density increases exponentially with the liquid pressure:

ρL=ρL0epp0βL,

where:

  • βL is liquid bulk modulus.

  • ρL is liquid density.

  • ρL0 is liquid density at reference pressure.

  • p is liquid pressure.

  • p0 is reference pressure. By default, the block assumes reference pressure to be the atmospheric pressure, 0.101325 MPa, but you can specify a different value.

In systems where the liquid pressure can change over a wide range, and the assumption of constant bulk modulus is not valid anymore, you can use the Isothermal bulk modulus model parameter to define the liquid bulk modulus as a linear function of pressure:

βL=βL0+Kβp(pp0),

where:

  • βL0 is liquid bulk modulus at reference pressure.

  • Kβp is the coefficient of proportionality between the bulk modulus and pressure increase.

If liquid pressure decreases below the reference pressure p0, the liquid bulk modulus value in the previous equation can become negative, which is nonphysical. To ensure that the liquid bulk modulus always stays positive, use the Minimum valid pressure parameter to specify the minimum valid pressure, pmin:

pmin>p0βL0Kβp.

If liquid pressure drops below the Minimum valid pressure parameter value, simulation issues an error.

Fluid Models with Entrained Air

In practice, working fluid is a mixture of liquid and a small amount of entrained air. To model this type of fluid, specify a nonzero value for the Entrained air-to-liquid volumetric ratio at atmospheric pressure parameter, but keep the Entrained air model as Constant.

The mixture density at a given pressure is defined as the total mass of liquid and entrained air over the total volume of the liquid and the entrained air at that pressure. While the total mass of the mixture is conserved as the pressure changes, the mixture volume does not stay constant. The entrained air is given by a volumetric fraction:

α0=Vg0Vg0+VL0,

where:

  • α0 is entrained air-to-liquid volumetric ratio at reference (atmospheric) pressure.

  • Vg0 is air volume at reference pressure.

  • VL0 is pure liquid volume at reference pressure.

The entrained air is assumed to follow the ideal gas law. The compression or expansion of air in the liquid is a polytropic process, in which the air pressure and liquid pressure are identical:

Vg=Vg0(p0p)1/n,

where:

  • Vg is air volume.

  • n is air polytropic index.

To model the air dissolution effects into the fluid, select the Model air dissolution check box.

The process of dissolving air into the fluid is described by Henry’s law. At pressures less than or equal to the reference pressure, p0 (which is assumed to be equal to atmospheric pressure), all the air is assumed to be entrained. At pressures equal or higher than pressure pc, all the entrained air has been dissolved into the liquid. At pressures between p0 and pc, the volumetric fraction of entrained air that is not lost to dissolution, θ(p), is a linear function of the pressure, and is approximated by a third-order polynomial function to smoothly connect the density and bulk modulus values between the three pressure regions:

θ(p)={1,pp00,ppc1(3(pcppcp0)22(pcppcp0)3),p0<p<pc.

Data Visualization

The block provides the option to plot the specified fluid properties (density and isothermal bulk modulus) as a function of pressure. Plotting the properties lets you visualize the data before simulating the model.

To plot the data, right-click the Isothermal Liquid Properties (IL) block in your model and, from the context menu, select Foundation Library > Plot Fluid Properties. Use the drop-down list located at the top of the plot to select the fluid property to visualize. Click the Reload button to regenerate a plot following a block parameter update.

Isothermal Liquid Properties Plot

Examples

Ports

Conserving

expand all

Isothermal liquid conserving port that connects the block to the network. You can connect it to any point on an isothermal liquid connection line in a block diagram. When you connect the Isothermal Liquid Properties (IL) block to a connection line, the software automatically identifies the isothermal liquid blocks connected to the particular circuit and propagates the liquid properties to all the blocks in the circuit.

Settings

expand all

Liquid

Density of the isothermal liquid at atmospheric pressure, with no entrained air.

Select the bulk modulus model for the isothermal liquid:

  • Constant — The bulk modulus is constant.

  • Linear function of pressure — The bulk modulus is a linear function of pressure.

Coefficient of proportionality between the bulk modulus and pressure increase.

Dependencies

Enabled when the Isothermal bulk modulus model parameter is set to Linear function of pressure.

Isothermal bulk modulus of the liquid at atmospheric pressure, with no entrained air.

Kinematic viscosity of the isothermal liquid at atmospheric pressure.

Absolute pressure of the environment.

Lowest pressure allowed in the isothermal liquid network. Depending on the Pressure below minimum valid value parameter value, the simulation can issue an error or warning when pressure is out of range.

Select what happens if the fluid pressure goes below Minimum valid pressure during simulation:

  • None ― The block does not return an error if the properties go out of range.

  • Warning ― The block issues a warning, but continues the simulation.

  • Error ― The block returns an error and stops the simulation.

Entrained Air

Volumetric fraction of air that is entrained in the fluid mixture at atmospheric pressure.

Air polytropic index. The default value of 1 represents an isothermal process, which is consistent with the assumptions of the isothermal liquid domain.

Air density at atmospheric condition.

Select the air dissolution model for the isothermal liquid:

  • If the check box is cleared, the amount of entrained air is constant. Air dissolution is not modeled.

  • If the check box is cleared, the entrained air can dissolve into liquid. The amount of dissolved air is a function of pressure.

Pressure at which all entrained air in the liquid is dissolved.

Dependencies

To enable this parameter, select the Model air dissolution check box.

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.

Version History

Introduced in R2020a

expand all