how can I plot
1 view (last 30 days)
Show older comments
sigma_0 = 2;
r = 1:0.1:2;
ksi = 1./r;
theta = 0;
sigma_r = (1/2.*sigma_0.*(1-(ksi.^2)))-(1/2.*sigma_0.*(1+(3.*(ksi.^4))-(4.*(ksi.^2))).*cos(2.*theta))
How can I show this as theta 0, 90, 180 and 270, all in one chart, depending on sigma r?
2 Comments
Manikanta Aditya
on 25 Mar 2024
Hey,
Check this:
% Constants
sigma_0 = 2;
theta_deg = [0, 90, 180, 270]; % Degrees
theta_rad = deg2rad(theta_deg); % Convert degrees to radians
% Variable
r = 1:0.1:2;
% Pre-allocate sigma_r for efficiency
sigma_r = zeros(length(r), length(theta_rad));
% Calculate sigma_r for each theta
for i = 1:length(theta_rad)
theta = theta_rad(i);
ksi = 1./r;
sigma_r(:, i) = (1/2.*sigma_0.*(1-(ksi.^2))) - (1/2.*sigma_0.*(1+(3.*(ksi.^4))-(4.*(ksi.^2))).*cos(2.*theta));
end
% Plotting
figure; % Create a new figure
hold on; % Hold on to plot multiple lines
colors = ['r', 'g', 'b', 'k']; % Colors for each theta
for i = 1:length(theta_rad)
plot(r, sigma_r(:, i), 'Color', colors(i), 'DisplayName', sprintf('\\theta = %d°', theta_deg(i)));
end
hold off;
xlabel('r');
ylabel('\sigma_r');
title('\sigma_r vs. r for \theta = 0, 90, 180, and 270 degrees');
legend('show');
grid on;
Answers (1)
Hassaan
on 25 Mar 2024
sigma_0 = 2;
r = 1:0.1:2; % Range of r
theta_deg = [0, 90, 180, 270]; % Angles in degrees
theta_rad = deg2rad(theta_deg); % Convert angles to radians
% Preallocate matrix for sigma_r values
sigma_r = zeros(length(r), length(theta_rad));
% Calculate sigma_r for each theta
for i = 1:length(theta_rad)
ksi = 1./r;
theta = theta_rad(i);
sigma_r(:, i) = (1/2.*sigma_0.*(1-(ksi.^2))) - (1/2.*sigma_0.*(1+(3.*(ksi.^4))-(4.*(ksi.^2))).*cos(2.*theta));
end
% Plot sigma_r vs r for each theta
figure;
plot(r, sigma_r, 'LineWidth', 2);
xlabel('r');
ylabel('\sigma_r');
title('\sigma_r vs r for Different \theta Values');
legend('0°', '90°', '180°', '270°');
grid on;
-----------------------------------------------------------------------------------------------------------------------------------------------------
If you find the solution helpful and it resolves your issue, it would be greatly appreciated if you could accept the answer. Also, leaving an upvote and a comment are also wonderful ways to provide feedback.
It's important to note that the advice and code are based on limited information and meant for educational purposes. Users should verify and adapt the code to their specific needs, ensuring compatibility and adherence to ethical standards.
Professional Interests
- Technical Services and Consulting
- Embedded Systems | Firmware Developement | Simulations
- Electrical and Electronics Engineering
Feel free to contact me.
0 Comments
See Also
Categories
Find more on Introduction to Installation and Licensing in Help Center and File Exchange
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!