How can I modify figure's property inspector elements through code?

I've a set of timeseries the I received from a SIMULINK model, then I use the subplit funcitonality to show the results using the following code %Powers Plot below

then I would have to open property inspector in order to modify the FontName, some of the xaxis and yaxis limits as in here:

Q1 : Can I find a way to automatically adjust the FontName, Axes limits by adjusting the code below???

If not, is there a way to set the defaults parameter for the figure inspector properties, so when the figure is printed it would use these values.

I've seen some documnetation, answers where I can set the limits, but for a one-plot figure, in my case I am using subplot, I want to be able to adjust limits for each subplot.

Also, note I am using timeseries plot, which is not straight forward as just plot(x,y)

Code:

% Powers Plot
 subplot(4,1,1 )
    Power_Load.Name = 'Demand Power';
    loadpowerplot= plot(Power_Load);
    ylabel(' Demand Power (W)')
    xlabel(' Time (h) ') 
    xaxisHours;

subplot(4,1,2 )
    Power_PV.Name = 'Solar Power ';
    plot(Power_PV)
    ylabel(' Solar Power (W) ')
    xlabel(' Time (h) ') 
    xaxisHours;
 
subplot(4,1,3 )
    Power_battery.Name = ' Battery Power (W) ';
    plot(Power_battery)
    ylabel(' Battery Power (W) ')
    xlabel(' Time (h) ') 
    xaxisHours;

 subplot(4,1,4 )
     Power_SC.Name = ' Supercapacitor Power ';
    plot(Power_SC)
    ylabel(' Supercapacitor Power (W)) ')
    xlabel(' Time (h) ') 
    xaxisHours;
    

PS: the xaxisHours is a code I made that will make the x axis values from seconds to hours and it's as follows:

    xaxisHours.m
    grid on
    xticks(0:60*60:24*60*60)
    xticklabels({'0','1','2','3','4','5','6','7','8','9','10','11','12','13','14','15','16','17','18','19','20','21','22','23' })

[Jonas]

you can set the Font by specifying it in the label commands, e.g.

ylabel('y-axis','FontName','This is the name of your font')

you can specify the ylimits by calling in every subplot after plotting by calling

 ylim([lower upper])

To change all font names after all plotting was done you can also search for all objects with a fontName property in the current figure by

 objs=findall(gcf,'-property','FontName')

and then setting it to the font name you want

 set(objs,'FontName','YourFontName')

[z8080]

Dear Mohamed Numair, you've been given an answer more than a month ago. Just curious: do you not find it appropriate to say thank you?

[Mohamed Numair]

@Jonas Thank you so much, that should help.

@z8080 I just say Jonas' comment just now, because I got an email notificaiton for your comment. Also, it doesn't show as an Answer so my question looked like it had 0 Answers all along.

[Jonas]

my bad, i will post a copy of my comment as answer below

Answer 1

[Jonas]

you can set the Font by specifying it in the label commands, e.g.

ylabel('y-axis','FontName','This is the name of your font')

you can specify the ylimits by calling in every subplot after plotting by calling

ylim([lower upper])

To change all font names after all plotting was done you can also search for all objects with a fontName property in the current figure by

objs=findall(gcf,'-property','FontName')

and then setting it to the font name you want

set(objs,'FontName','YourFontName')

[Mohamed Numair]

Much Appreciated.