Assistance with Load Flow Analysis in IEEE 34 Distribution Network on MATLAB-Simulink

Hello,
I am working with the IEEE 34-bus distribution network in MATLAB-Simulink. When running the load flow analysis after setting up the buses, I encountered the following error message:
"Warning: Matrix is close to singular or badly scaled. Results may be inaccurate. RCOND = 1.218374e-17."
Given that this is an unbalanced system, could you please advise on the potential causes of this issue?How to solve it? Additionally, are there alternative methods or tools within MATLAB-Simulink to handle load flow analysis for such systems?
Thank you for your assistance.
Best regards,

Answers (1)

I understand that you are facing an error while running the load flow analysis of IEEE 34-bus system.
The error message “Matrix is close to singular or badly scaled” typically indicates numerical instability or issues with the system setup often due to a matrix being close to singular or badly scaled.
The error can be rectified by:
  • Ensure that all bus data, line impedances, and load values are entered correctly. Small errors in data can lead to numerical instability.
  • Ensure there are no lines with zero or extremely high impedance values, as these can cause singularities in the admittance matrix.
  • Verify that all buses are connected and there are no isolated buses or islands within the network.
  • The IEEE 34-bus system is inherently unbalanced, which can cause convergence issues in load flow analysis.
  • In unbalanced systems, ensure that the load and generation data are accurately represented for each phase.
  • Scale the system parameters to improve numerical stability. This can involve normalizing the values to a common base.
  • Ensure that the network configuration is correct and all elements are properly connected.
  • Switch to more robust load flow solvers like Newton-Raphson or Fast Decoupled methods, which are better suited for handling unbalanced systems.
  • Adjust the tolerance settings for the load flow solver to allow for better convergence.
  • Break down the network into smaller sections and solve them individually before combining the results.
You can refer the below file exchange link on IEEE 34-bus system and load flow analysis
Alternatively, you can use
  • MATLAB’s Simscape Electrical toolbox provides tools for detailed modelling and simulation of electrical power systems, including unbalanced load flow analysis.
  • Use the powergui block in Simulink to perform load flow analysis. It provides options for different solvers and can handle unbalanced systems.
  • Write custom MATLAB scripts to handle specific aspects of the load flow analysis, allowing for more control over the numerical methods used.
Hope this helps!

5 Comments

Can you explain the different methods available for solving the power flow problem? I've verified that my model matches the IEEE 34 standard, but are there any alternative approaches I could use to solve the problem at this point?
The system described in the first link is the one I am currently using.
@Asi angel. You said that you were bale to match the results to IEEE bench mark values. Actually I myself am trying to match it. I was able to get the error down to 0.6% for Bus Voltage magnitude and 0.6 deg for Bus voltage angle. except for Bus 888, 890 for which the errors are 2.8% at maximum. And these two busus come after step down tranfromer. Can you please tell me about your results or better yet I can share my model (phasor). So that you can check for any discrepancies ?
Hi, I'm working on a project, and I need a functional IEEE 34-bus test feeder. Does anyone here have one they could share? I've been struggling with this same issue for a while, and it's been driving me crazy.
Answer from AI:
Depending on your specific application (e.g., dynamic transients, phasor-based studies, or steady-state unbalanced load flow), there are several highly functional, pre-built models of the IEEE 34-bus test feeder designed natively for MATLAB and Simulink.
The top available options categorized by their use case include:
1. For Simulink-Based Simscape / Specialized Power Systems
If you need a graphical model to run time-domain or steady-state simulations, several well-regarded models are hosted directly on the MathWorks File Exchange:
2. For Programmatic or GitHub-Based Workflows
  • If you prefer a repository that maps strictly to the official IEEE-PES Distribution System Analysis Subcommittee specifications, you can clone the liyifu93 GitHub Repository. It contains an orchestrated programmatic structure to initialize parameters via .m scripts and run the companion Simulink feeder seamlessly. [1]
3. Quick Comparison: Steady-State vs. Dynamic Modeling
Model Type Best Used For Pros Toolbox Requirement
Phasor Voltage profile analysis, slow Faster computation, Simscape Electrical /
dynamics, renewable easy initialization Specialized Power Systems
integration
Discrete / EMT Fault analysis, transient High precision, Simscape Electrical /
overvoltages, power captures wave Specialized Power
electronics transients Systems
Tips for Implementation:
  • Unbalanced Systems: Keep in mind that the IEEE 34-bus system is inherently unbalanced and contains single-phase and two-phase laterals. If you run power flows manually, standard positive-sequence solvers (like basic MATPOWER) will not work natively unless modified into a 3-phase framework. Ensure your Simscape solver is configured for unbalanced networks. [1, 2, 3]
  • Voltage Regulators & Transformers: Pay close attention to the target model's parameter script. The IEEE 34-bus utilizes unique in-line transformers and automatic step-voltage regulators that require proper initialization taps to converge accurately. [1]

Sign in to comment.

Products

Release

R2021a

Asked:

on 11 Sep 2024

Commented:

on 17 Oct 2026 at 21:51

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!