Simulation results on command window

How do I display the average for the outputs of SNR, SNRM and SNRP on the command window or workspace?

It keeps showing me 3 numbers like this.

function [ SNR, SNRM, SNRP ] = SNRmulfication( Ip,Is,Nrep,M)
%SNR=SN ratio after multification
%SNM=SN ratio after signal mutification
%SNRP=SN after power multification
%This code simulates the signal to noise multification

%This is without a multification factor
SD=sqrt(Ip); %Standard deviation of power.
for i=1:Nrep
Inp=randn(1,Nrep)*SD+Ip; %Initial power fluctuation
    S=0.1*Inp; %Power to Signal conversion
    SD1=sqrt(S); %Standard deviation of signal
    Res=randn(1,1)*SD1+S; %Detected Signal
    Signal=mean(Res); %Mean Detected Signal
    Noise=std(Res); %Noise
    SNR(i)=Signal/Noise %Signal to noise ratio without multification
 end
%This multiply the signal after detection
for i=1:Nrep
    Inp=randn(1,Nrep)*SD+Ip; %Initial power fluctuation
    S1=0.1*Inp; %Power to Signal conversion
    SD1=sqrt(S1);%Standard deviation of signal
    Res1=randn(1,1)*SD1+S1; %Detected Signal
    Rep=Res1*M; %Detected Signal after multification
    SD11=sqrt(Rep);
    Rep1=Rep+randn(1,1)*SD11+Rep; %Signal fluctuation after multification
    Signal1=mean(Rep1); %Mean Detected Signal
    Noise1=std(Rep1); %Noise
    SNRM(i)=Signal1/Noise1 %Signal to noise
end
%This multiflies the initial power
Ip1=Ip*M; %Power after multification
SD2=sqrt(Ip1); %Standard deviation of multificated power
for i=1:Nrep
    Inp2=randn(1,Nrep)*SD2+Ip1; %power fluctuation
    S2=0.1*Inp2; %Power to Signal conversion
    SD3=sqrt(S2); %Standard deviation of the signal
    Res2=randn(1,1)*SD3+S2; %Detected signal fluctuation
    Signal2=mean(Res2); %Mean signal
    Noise2=std(Res2); %Noise
    SNRP(i)=Signal2/Noise2 %Signal to noise ratio after power multification
end
end
%Copy this to command window to simulate "SNRmulfication(1000,100,3,100);"

Answer 1

[Kevin Phung]

What you can do is calculate the average outside of the loop, for example, for snrm:

for i=1:Nrep
    Inp=randn(1,Nrep)*SD+Ip; %Initial power fluctuation
    S1=0.1*Inp; %Power to Signal conversion
    SD1=sqrt(S1);%Standard deviation of signal
    Res1=randn(1,1)*SD1+S1; %Detected Signal
    Rep=Res1*M; %Detected Signal after multification
    SD11=sqrt(Rep);
    Rep1=Rep+randn(1,1)*SD11+Rep; %Signal fluctuation after multification
    Signal1=mean(Rep1); %Mean Detected Signal
    Noise1=std(Rep1); %Noise
    SNRM(i)=Signal1/Noise1; %Signal to noise
end
avg_SNRM = mean(SNRM)

%next for looop

note: dont forget to add ';' to suppress the output of each iteration

[Chanaka Navarathna]

It has worked and thank you for your time.