Community Profile

photo

Javier Gazzarri


MathWorks

17 total contributions since 2014

Contact

Javier Gazzarri's Badges

  • Personal Best Downloads Level 4
  • First Review
  • 5-Star Galaxy Level 4
  • First Submission
  • 3 Month Streak
  • Revival Level 2
  • Knowledgeable Level 2
  • First Answer

View details...

Contributions in
View by

Submitted


Lithium Ion Battery Pack with Cell Balancing
A 3s1p lithium ion battery pack is charged with a CCCV profile and passive balancing

1 year ago | 116 downloads |

Submitted


Lithium Battery Model, Simscape Language and Simulink Design Optimization
Lithium ion battery parameter estimation, simulation, and pack design

2 years ago | 532 downloads |

Thumbnail

Answered
¿Why the battery (electrical source component in SimPowerSystem Matlab/Simulink toolbox) discharge at the same rate with different capacities?
Hello, Jorge, I am attaching a model like you describe above and it seems to work correctly for me. Please make sure you cli...

4 years ago | 0

Answered
Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid
Hi, Md., You can still use SPS in that case. The main difference with SimElectronics is that the latter models all nonlineari...

4 years ago | 0

Answered
Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid
Hello, Md., If the AC part of your system is three-phase and you can neglect thermal effects on the semiconductor devices and...

4 years ago | 0

Answered
How can I generate the setup of AC sweep for AC Voltage source in either Matlab or simulink?
Hello, Robert, I believe the Chirp Signal may do the job for you. It is in the Sources section of the Simulink library. Be...

4 years ago | 0

| accepted

Answered
Problems with model behaviour, hanging-up in a loop.
Hello, Joel, Would you please attach the model to this thread so I can take a look and try to better understand the issue? ...

5 years ago | 0

| accepted

Answered
How to model a solar powered electric grid in Simulink?
Hello, Faraz, I suggest you consider the use of SimPowerSystems for your design. You can find some examples here: http://w...

5 years ago | 1

| accepted

Answered
Simscape thermal mass discrete model
Dear Lalumet, A discrete solver can be used if you set up "Use Local Solver" in the Simscape Solver configuration block. Ple...

5 years ago | 0

Answered
How to make a Variable resistor in Sim powersystem not Simscape.
Hello, Adroit, You can combine a current meter and a controlled voltage source to create a variable resistor. Please see att...

5 years ago | 2

| accepted

Answered
Battery Model Simulink for 12V
Hi, Samad, Please open the battery cell block and comment out the SOC, DOC, and T blocks. This will prevent the second error ...

5 years ago | 1

| accepted

Answered
How to connect generic battery to an electrical circuit which is created using Simscape??
Hello, Mirza, Yes, that is possible. There are a couple of options: 1) Use SimPowerSystems Simscape Components. The blocks...

5 years ago | 0

| accepted

Answered
lead acid battery simulink
Hello, Simon, You may want to check this submission for an example of what you are trying to model: http://www.mathworks.c...

5 years ago | 0

Answered
Battery Model Simulink for 12V
Hi, Samad, The series connection in Simscape is realized connecting the + terminal of each cell to the - terminal if the adja...

5 years ago | 0

Answered
Bringing battery simulation results (parameter estimation) to hardware
Hello, Valentin, Designing an accurate SOC estimator for embedded implementation is a very involved task that goes beyond des...

5 years ago | 0

| accepted

Answered
How to connect generic battery to an electrical circuit which is created using Simscape??
Hello, Mirza, Can you please attach a screenshot of your model so that I can take a look? Your problem is typically related ...

5 years ago | 0

Answered
Error with Simscape simulating
Hello, Nikolaos, Your model is missing an electrical reference (ground). Please add one and let me know if you still get an e...

5 years ago | 1

Answered
Recharge battery by induction on simulink
Hello, Titouan, Please try inserting an electrical reference block on the right hand side of your magnetic circuit. It needs ...

5 years ago | 0

| accepted