INFOZOU
Engineer and Doctor in electrical engineering Automatic and Industrial Computers Computer systems and mechatronics
Statistics
RANK
943
of 288,908
REPUTATION
70
CONTRIBUTIONS
0 Questions
23 Answers
ANSWER ACCEPTANCE
0.00%
VOTES RECEIVED
27
RANK
13,813 of 19,495
REPUTATION
16
AVERAGE RATING
5.00
CONTRIBUTIONS
1 File
DOWNLOADS
3
ALL TIME DOWNLOADS
68
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Content Feed
Error in Simulink model with Arduino mega....
<https://www.mathworks.com/matlabcentral/answers/106975-error-downloading-simulink-model-to-arduino-mega-2560-rev3> <http://w...
7 years ago | 1
Linking Simplorer with Matlab/Simulink R2015b and Higher?
<https://www.mathworks.com/matlabcentral/answers/160102-how-do-i-link-simplorer-to-simulink> <https://www.mathworks.com/help/...
7 years ago | 0
How to run state space system with D matrix in Simulink?
https://www.mathworks.com/help/simulink/slref/statespace.html
7 years ago | 1
How do I save a Simulink project, with many levels of Sub-systems, so that when I next open the project all subsystems are automatically zoomed to fit the window?
https://www.mathworks.com/matlabcentral/answers/132519-startup-from-top-simulink-model
7 years ago | 1
How can I do a Processor in Loop (Arduino + Simulink)?
https://groups.google.com/forum/#!topic/comp.soft-sys.matlab/07fRaDXP7pk https://www.mathworks.com/matlabcentral/answers/...
7 years ago | 1
Single Acting Hydraulic Piston
https://www.mathworks.com/videos/modeling-a-hydraulic-actuation-system-68833.html https://www.mathworks.com/help/physmod/hydr...
7 years ago | 1
Why are my simulink library blocks highlighted?
https://www.mathworks.com/help/simulink/ug/displaying-signal-sources-and-destinations.html
7 years ago | 1
How do I add a specific FPGA in MATLAB HDL Coder?
https://www.mathworks.com/solutions/fpga-design/simulink-with-xilinx-system-generator-for-dsp.html https://www.mathworks.com/he...
7 years ago | 1
| accepted
How to create Nyquist Frequency folding diagram.
https://www.mathworks.com/help/control/ref/nyquist.html
7 years ago | 1
HOW TO CONTROL A BLDC MOTOR WITH A PR CONTROLLER?
You clicked a link that corresponds to this MATLAB command: power_brushlessDCmotor Run the command by entering it in the MAT...
7 years ago | 1
what is consequent and antecedent in fuzzy inference system
https://www.mathworks.com/help/fuzzy/fuzzy-inference-process.html
7 years ago | 1
How can i use fuzzy controller in system generator
There are not all supported blocks in system generator toolbox. I have tried to do it, but, I do not find the neccesary blocks t...
7 years ago | 1
Fuzzy Logic Rule editor adding weights to rules in one shot than manually typing each one out for each rule
http://www.mathworks.com/help/fuzzy/simulate-fuzzy-inference-systems-in-simulink.html
7 years ago | 1
How to train Mamadani Fuzzy inference system ?
Try the following commands: a = readfis('tipper'); plotmf(a,'input',1) http://www.mathworks.com/help/fuzzy/plotmf.html To ver...
7 years ago | 1
What method does MATLAB use to compute test error in ANFIS toolbox?
RMSE ftp://ftp.unicauca.edu.co/Documentos_Publicos/Facultades/FIET/DEIC/Materias/Control%20Inteligente/clases_2006a/Parte%20III...
7 years ago | 3
| accepted
Je suis dans le besoin de pv contrôle MPPT final avec le modèle flou, si vous avez s'il vous plaît s'il vous plaît envoyez - le à bassem.physique@hotmail.com
The following link describes the modelisation of MPPT model controlled by fuzzy logic using Simulink Matlab : http://docplayer.f...
7 years ago | 2
| accepted
how can set a membership function in matlab
You can use the command "fuzzy" in Matlab command and fix the different parameters (memberships of inputs and output..). In this...
7 years ago | 1
Create a function in simulink
You can use the block "from workspace" from * * *sources*** in Simulink. For your case, you can use directly "reshape", "add", ...
7 years ago | 2
| accepted
LED lamp model using simulink
http://www.mathworks.com/help/simulink/ug/control-an-led-display.html https://www.mathworks.com/help/physmod/elec/ref/lightem...
7 years ago | 2
How can i make a .fis model file to work with FLC toolbox and use it with Arduino for obstacle avoidance robot?
File>import>from workspace and choose the file a.fis direction. There are arduino toolbox in Simulink, however, you should veri...
7 years ago | 1
how can i solve this error? see in picture
You should verify system and fuzzy logic controller parameters. The picture is not very clear. Please could you provide a clear ...
7 years ago | 1
I have problem while running my Micro hybrid DC simulation model & it takes more time(10-11 hr) for running.
I have the same problem while running my system (robot including BDCM motor+fuzzy logic controller )simulation model and it take...
7 years ago | 1