Mahmoud Saleh
City Collage of New York
My research involves microgrid control and design, microgrids clustering, intermittency of renewable-based MG, and integration of microgrids to electric power grids. Also, I investigate the feasibility of smart grid implementations. Moreover, I am involved in writing technical proposals.
Please contact me for collaboration and discussing my recent work regarding electric energy markets, cyber-attacks, and machine learning application in power systems.
https://www.linkedin.com/in/mahmoud-saleh/
Statistics
RANK
2,719
of 295,467
REPUTATION
22
CONTRIBUTIONS
0 Questions
18 Answers
ANSWER ACCEPTANCE
0.00%
VOTES RECEIVED
7
RANK
671 of 20,234
REPUTATION
2,701
AVERAGE RATING
4.90
CONTRIBUTIONS
5 Files
DOWNLOADS
103
ALL TIME DOWNLOADS
24881
RANK
of 153,912
CONTRIBUTIONS
0 Problems
0 Solutions
SCORE
0
NUMBER OF BADGES
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Submitted
Applications of Complex Network Analysis in Electric Power Systems Code
Code used in the paper: Applications of Complex Network Analysis in Electric Power Systems
6 years ago | 5 downloads |
Simple DC/DC Converter
I would say take a look at the following models, you should find the detailed modelling steps: https://www.mathworks.com/matlab...
7 years ago | 1
i konw to make bidirectional dc to dc converter.but it does not give the perfect answer.please check and give me the solution.i have attached my design
Please check those two models for detailed modelling of bidirectional converter: https://www.mathworks.com/matlabcentral/fileex...
7 years ago | 0
how to select the output current in boost converter?
You should find the detailed answer of how to design a boost converter inside this model: https://www.mathworks.com/matlabcentr...
7 years ago | 1
Electric Rail System Model
I do not have this model, but you can check this model and let me know if you have further question: https://www.mathworks.co...
7 years ago | 0
how Dc DC boost converter with PID can be achieved in simulink.
You might find some portion of the model you are asking for in the two models mentioned below, but off course you will have to a...
7 years ago | 0
How to design DC-DC boost converter using simulink (Current mode control)
Check out those models: https://www.mathworks.com/matlabcentral/fileexchange/63330-current-controller-dc-dc-bidirectional-con...
7 years ago | 1
Boost Converter in Simulink
Check this model and compare: https://www.mathworks.com/matlabcentral/fileexchange/63949-voltage-control-dc-dc-boost-converte...
7 years ago | 0
Need help modeling a Buck/Boost Converter in Simulink/Simscape
Check out those two models for boost and bidirectional dc/dc converter. An explanation can be found in the Simulink model. Those...
7 years ago | 0
How to Parallel Boost converter to suply dc load
If the PIs are meant to fix the voltage across the 60 ohms resistance. Then, this is a droop control where the load is being sha...
7 years ago | 0
capacitor and inductor in boost converter
Basically, without them the output of the converter whether it is voltage or current will be square wave, on/ off. Most of loads...
7 years ago | 0
DC DC Converter with battery as a load
Hi, You need a boost converter to boost the voltage from (16-32V) to 60V, or you can use bidirectional converter, you can use...
7 years ago | 2
Current mode controlled DC DC boost converter?
Hi, Check this model and let me know if you have further question: https://www.mathworks.com/matlabcentral/fileexchange/63330...
7 years ago | 0
design of dc dc bidirectional charge controller for lead acid battery in simulink?
Hi, Check out this model: https://www.mathworks.com/matlabcentral/fileexchange/63791-voltage-control-dc-dc-bidirectional-conv...
7 years ago | 0
How will I simulate a circuit of Bidirectional DC-DC converter fed drive using MOSFETs for electric vehicle system ?
Hello, You can start by checking out this model: https://www.mathworks.com/matlabcentral/fileexchange/63791-voltage-control-dc-d...
7 years ago | 0
how to draw a simulation model of bidirectional converter??
Check out those two models: https://www.mathworks.com/matlabcentral/fileexchange/63330-current-controller-dc-dc-bidirectional...
7 years ago | 0
Boost converter in Simulink
This block is not compatible with the rest of the model. Check this model: https://www.mathworks.com/matlabcentral/fileexchan...
7 years ago | 0
Submitted
Voltage Control DC/DC Boost Converter
DC/DC Boost Converter can be used to maintain the DC bus voltage
7 years ago | 23 downloads |
Submitted
DC traction system, Electrical train model
A DC traction system, 2 substations, with a train moving between 3 passenger stations were modeled
7 years ago | 18 downloads |
Submitted
Current Controller DC/DC Bidirectional Converter
Current Controller DC/DC Bidirectional Converter Model with a detailed description
7 years ago | 36 downloads |
Submitted
Voltage Control DC/DC Bidirectional Converter
Voltage Controlled DC/DC Bidirectional Converter, multiple Simulink version is uploaded
7 years ago | 20 downloads |
Medium voltage distribution network Simulink model
Check this link: http://www.mathworks.com/matlabcentral/fileexchange/index?utf8=%E2%9C%93&term=ieee
10 years ago | 2
How can I modelize the IEEE 123 Node Feeder on Matlab/Simulink. please help me
Check this link: http://www.mathworks.com/matlabcentral/fileexchange/index?utf8=%E2%9C%93&term=ieee
10 years ago | 0
| accepted