Community Profile

# Venkatesh Chilapur

Last seen: 4 days ago Active since 2017

All

#### Content Feed

View by

Submitted

DC-DC Buck Converter Simulink Model using STM32 BG474EDPOW1
This submission contains an example model that implements a DC-DC Buck Converter using STM32 BG474EDPOW1 Discovery Kit.

Submitted

Simulink Reference Application Examples for TI C2000
This repository will host Simulink reference application examples using Embedded Coder TI C2000 Support Package.

Solved

Whether the input is vector?
Given the input x, return 1 if x is vector or else 0.

10 months ago

Solved

Flip the vector from right to left
Flip the vector from right to left. Examples x=[1:5], then y=[5 4 3 2 1] x=[1 4 6], then y=[6 4 1]; Request not ...

10 months ago

Solved

Arrange Vector in descending order
If x=[0,3,4,2,1] then y=[4,3,2,1,0]

10 months ago

Solved

Find the sum of all the numbers of the input vector
Find the sum of all the numbers of the input vector x. Examples: Input x = [1 2 3 5] Output y is 11 Input x ...

10 months ago

Solved

Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

10 months ago

Hi Federico, See if this helps! problem with F28379D - MATLAB Answers - MATLAB Central (mathworks.com) Regards, Venkatesh C

1 year ago | 0

Problems with data visualization in parameter tuning with serial communication and buffered data (Ti C2000)
Hi Dominik, See if you can use the two model approach. How can I use a two model approach for signal logging and parameter tun...

1 year ago | 0

| accepted

Failed to build model for TI-C2000 with Simulink
Hi Wei, Make sure if you have followed all the steps related to 'setup' of the supportpackage. More details can be found here: ...

1 year ago | 0

is simulink support for Aurix TC297 microcontroller for Model Based Design
Hi Manohar, There can be following approaches (Option 2 or 3 in your case): The board or the MCU is already supported by MATLA...

1 year ago | 0

I2C Transmit com => Launchpad F28379D freeze

1 year ago | 0

Generate C code for MC33771 and S32K for SOC/SOH standlone oepartion
Hi Balwinder, There can be following approaches (Option 2 or 3 in your case): The board or the MCU is already supported by MAT...

1 year ago | 1

Creating bit stream for SPI devices
Hi, Please refer the shipping example - c28x_spi_eeprom/Write EEPROM Data which will provide a very good overview on how you ca...

1 year ago | 1

STM32F767ZI Simulink - "The target configuration uses time from a local timer, which is not based on simulation time"
Hi, This is a known limitation. If you use HW timer for getting the timestamps, you can't use Scope/Display to visualize signal...

1 year ago | 0

How to give control command through MATAB to Code Composer Studio code
Please refer the following example which showcases the 2 model approach. Here you can command a control value from Host model to...

1 year ago | 0

Texas Instruments C2000 PMSM Control
Please find the following details on TIC2000 SPKG reference material: (Under section 3 below, one can find Motor control example...

1 year ago | 0

Overcurrent protection using One shot trip TI 28379D

1 year ago | 0

Trip-zone using Embedded Coder Support Package for Texas Instruments
Hi Krishnan, You may also want to do the following settings: Upon the trip condition the above setting will esure the outp...

1 year ago | 0

CLA Compiler Errors Using Embedded Coder for Texas Instruments C2000 Processors
Hi Grant, We used your model and made couple of changes. Change from Switch to If-else Unit delay and Memory block at: gatedr...

2 years ago | 0

TMS320F28379D: Use DMA in CLA to Assign Counter Compare Values (Simulink Coder)
It is either DMA or CLA that can access the peripheral registers at a given time. We choose between either DMA or CLA to access...

2 years ago | 0

| accepted

Trip-zone using Embedded Coder Support Package for Texas Instruments
Hi Mohammed, On the ePWM block Mask you will find the Tab for Trip Zone configuration. Here you can enable CBC and OST trips he...

2 years ago | 0

C2000 series FFT analysis problem
Hi, Please check out this example and let me know if you have more questions. https://www.mathworks.com/help/supportpkg/texasi...

2 years ago | 0

PWM-triggered CLA in Embedded Coder
Hi, Please try attached model. You can get more details on the configurations around RT block from the model 'c28379D_datainte...

2 years ago | 0

PWM-triggered CLA in Embedded Coder
Hi, It is likely that the Class of the simulink parameter Cla_out might not be updated. It can be updated by following the bel...

2 years ago | 0

Code Replacement Library for TI C2000 Microcontrollers

2 years ago | 0

program will not fit into available memory ".cinit"

2 years ago | 0

| accepted

check connection between Dsp Ti c2000 board with matlab
Hi, There is a getting started video for Embedded Coder Support Package for Texas Instruments C2000 Processors which can help...

2 years ago | 0