photo

Yusuf Selim KARATAS


Last seen: 3 years ago |  Active since 2019

Followers: 0   Following: 0

Statistics

  • Thankful Level 1
  • Knowledgeable Level 1
  • First Answer
  • First Review

View badges

Feeds

View by

Question


SIMSCAPE Parameters from WorkSpcae
Dear All, I have a simscape model that has some parameters like SOC_points, T_points and C points. I enter cell_SOCpoints, cell...

3 years ago | 0 answers | 0

0

answers

Question


Version Control for slx Files
Dear All, We are currently using Version Control systems in our project on Matlab. Our project has .slx files and since .slx ...

3 years ago | 0 answers | 0

0

answers

Question


PROCESSOR IN THE LOOP - DATA PAYLOAD
Dear All, I am working on NXP S32K144 with MBD tools. What I am trying to is implementing Processor in the Loop Simulation with...

4 years ago | 0 answers | 0

0

answers

Question


Matlab Simulink RepMat Execution Time
Dear All, I need a significant help. I have a Simulink model that has a subsystem that takes a matris [3x1] and makes it [3x...

4 years ago | 1 answer | 0

1

answer

Question


SIMULINK PROFILER - NUMBER OF CALL
Hello everyone, I am trying to use Profiler function for SIL of one of the models that I have. I was checking number of call ...

4 years ago | 0 answers | 0

0

answers

Question


Design verifier Unsupported data pointer
Dear All, We are trying to use Simulink Design Verifier in one of our model to detect PIL problem(run time failure). But we g...

4 years ago | 1 answer | 0

1

answer

Question


PIL Communication Timeout for MPC57xx
Dear All, I am trying to use external mode for C2000 and PIL for MPC57xx. for C2000 even sample project model gives commun...

4 years ago | 0 answers | 0

0

answers

Question


SIMULINK WHILE LOOP with Estimator
Dear All, I am trying to build a while loop that tries to estimate future values. Block diagram is as below. Main Code ...

4 years ago | 0 answers | 0

0

answers

Question


C28x Memory Operations
Dear All, I am trying to add memory operations one of my complex model. But before directly implementing to complex one , I j...

4 years ago | 0 answers | 0

0

answers

Question


C2000 CAN RX
Dear All, I am using Simulink to build a model to receive CAN messages. You can see diagram below. I am getting "error: express...

4 years ago | 1 answer | 0

1

answer

Question


C2000 timer interrupt for 1 second
Dear All, I want to set 1 second timer in C2000 and output an analog signal. How can I do that? Can you help me? I have also ...

4 years ago | 0 answers | 0

0

answers

Question


C2000 SCI BYTES IN ONE FRAME
Dear All, I am trying to use C2000 SCI function. I need to send more than 1 BYTE in a frame to communicate with BQ76PL455EVM....

4 years ago | 0 answers | 0

0

answers

Question


F28379D READING VALUES FROM GPIO INPUT AND SCI RCV
Hello, I want to see whether a digital input is HIGH or LOW but scope and display always show 0 despite of changing voltage l...

5 years ago | 0 answers | 0

0

answers

Question


Data Store Memory to Global Workspace
Hello, I am using a function that reads some values from a data storage memeory and writes back to data storage memory. What ...

5 years ago | 1 answer | 0

1

answer

Question


28379D GPIO INPUT
Hi, I want to use GPIO input and want to see incoming signal on my computer but incoming signal always seem as 0 Zero. How ca...

5 years ago | 1 answer | 0

1

answer

Answered
C2000 F28379d SCIB
Hello Venkatesh, To be clear, you mean that you have tried and used succesfully SCI B on my model, am I right? Thanks.

5 years ago | 0

Question


C2000 SCI B and SCI C
Hi everyone, I am using 28379d LaunchPad and could not get any signal on SCI B and SCI C. I have attached model. Can you tell...

5 years ago | 0 answers | 0

0

answers

Answered
C2000 F28379d SCIB
Is there anyone that can help me on this issue ?

5 years ago | 0

Answered
Error in Code build for C2000 Piccolo F28027
I dont know the source of the problem. But I have learned that sometimes you need to change clock frequency on these boards. Kee...

5 years ago | 0

Question


C2000 F28379d SCIB
Hello, I need to use SCIB port of the F28379d on MATLAB Simulink. I assign some pins for SCIB communication and SCIC communic...

5 years ago | 3 answers | 0

3

answers

Question


SIMSCAPE INPUT FOR SOURCE CODE
Hello eveyone, I want to use a generate a temperature dependent voltage source in simscape by using dc voltage source. Temper...

5 years ago | 1 answer | 0

1

answer